View source for MSS60 Error: 2738, P0068, P0106, P2193

__FORCETOC__

====2738 - P0106====
{| class = "diyTable ecuFault"
|-
|'''Information saved in'''
|DME
|-
|'''Fault code'''
|2738 - P0106
|-
|'''Fault text'''
|Charge plausibility, diagnosis, cold-start strategy, bank 2
|-
|'''Fault description'''
|Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance
|-
|'''Condition for fault identification'''
|Test condition: * Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_LAM/AQ_DELTA_ML_MAX * Expansion factors (1.5 K_FPLAU_OBD_TE_F, KL_FPLAU_OBD_AQ_PSAU_CSS_F)
|-
|
|Terminal condition: Engine running
|-
|
|Voltage condition: None
|-
|'''Condition for fault memory entry'''
|10000 ms
|-
|'''Action in service'''
|1. Check induction system B1 for leaks
|-
|
|2. Replace intake manifold pressure sensor
|-
|'''Fault effect and breakdown warning'''
|MIL on after engine runs 2x
|-
|'''Driver information'''
|Warning light: MIL
|-
|'''Service instruction'''
|None
|}


====2738 - P0068====
{| class = "diyTable ecuFault"
|-
|'''Information saved in'''
|DME
|-
|'''Fault code'''
|2738 - P0068
|-
|'''Fault text'''
|Charge plausibility, diagnosis, cold-start strategy, bank 2
|-
|'''Fault description'''
|MAP/MAF - Throttle Position Correlation
|-
|'''Condition for fault identification'''
|Test condition: * Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_LAM/AQ_DELTA_ML_MAX * Expansion factors (1.5 K_FPLAU_OBD_TE_F, KL_FPLAU_OBD_AQ_PSAU_CSS_F)
|-
|
|Terminal condition: Engine running
|-
|
|Voltage condition: None
|-
|'''Condition for fault memory entry'''
|10000 ms
|-
|'''Action in service'''
|1. Check induction system B1 for leaks
|-
|'''Fault effect and breakdown warning'''
|MIL on after engine runs 2x
|-
|'''Driver information'''
|Warning light: MIL
|-
|'''Service instruction'''
|None
|}


====2738 - P2193====
{| class = "diyTable ecuFault"
|
|
|-
|'''Information saved in'''
|DME
|-
|'''Fault code'''
|2738 - P2193
|-
|'''Fault text'''
|Charge plausibility, diagnosis, cold-start strategy, bank 2
|-
|'''Fault description'''
|System Too Lean at Higher Load (Bank 2)
|-
|'''Condition for fault identification'''
|Test condition: * Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_LAM/AQ_DELTA_ML_MAX * Expansion factors (1.5 K_FPLAU_OBD_TE_F, KL_FPLAU_OBD_AQ_PSAU_CSS_F)
|-
|
|Terminal condition: Engine running
|-
|
|Voltage condition: None
|-
|'''Condition for fault memory entry'''
|10000 ms
|-
|'''Action in service'''
|1. Check induction system B1 for leaks
|-
|'''Fault effect and breakdown warning'''
|MIL on after engine runs 2x
|-
|'''Driver information'''
|Warning light: MIL
|-
|'''Service instruction'''
|None
|}